Personalised Robe & Pyjama Care Guide

Heat Transfer Vinyl adds a beautiful, customised touch to bridesmaid and bridal robes or pyjamas - but it also means you need to take extra care when washing, drying and removing creases to avoid damage such as peeling, cracking, or fading.

How to Safely Wash Personalised Robes and Pyjamas:

Everything is done to ensure that wearable robes and items arrive in perfect condition, they are always packed in individual plastic bags to keep the robes dirt and moisture-free during transit. However, if you would like to freshen up the robes before gifting or wearing them, here are some simple steps to ensure the longevity of your custom designs.

Hand Washing - For the gentlest clean:

  • Fill a basin or sink with cold water.
  • Add a small amount of mild detergent (free of bleach, fabric softener, or harsh chemicals). Do not add fabric softener.
  • Gently swirl the robe in the water. Avoid harsh rubbing or scrubbing, especially on the vinyl area.
  • Rinse thoroughly in cold water.
  • Gently press out excess water, do not wring it!

Washing Machine - An easier method but with more risks:

  • Keep the robe inside out.
  • It may help to place it in a mesh laundry bag to protect it.
  • Use a mild detergent: gentle, pH-neutral detergents designed for delicates or baby clothes.
  • Do not use fabric softener: the ingredients in fabric softener may break down the adhesive on Heat Transfer Vinyl and cause your personalisation to peel off the robe.
  • Use the delicate or hand-wash cycle with cold water only.
  • Wash with similar soft fabrics (no zippers or rough textures that could rub against the robe).

Skip the Dryer — Always air-dry!

  • Do not put the robe in the dryer. Heat can damage heat transfer vinyl in many ways: it melts the adhesive and can warp or crack the design.

  • Instead, lay it flat on a clean towel or hang it to air dry in a well-ventilated area.

  • Avoid direct sunlight, which can cause fading in both the satin and the vinyl.

How to Remove Creases from Personalized Satin Bridal Robes:

Your personalized satin bridal robe is the most photographed piece you’ll wear before walking down the aisle. But when it's pulled out of the package or unpacked after travel, chances are it may not look as smooth and flawless as you’d hoped. Don’t worry—those creases don’t stand a chance if you follow these gentle, satin-safe methods.

Why Satin Needs Special Care

Satin is sleek, soft, and luxurious, but it’s also sensitive to heat and friction. Add personalization—whether it’s embroidered, printed, or with vinyl lettering—and you’ve got an item that needs a bit of extra TLC. Here's how to remove wrinkles without damaging the robe or its custom design. 

1. Use a Steamer – The Safest Option

How to do it:

  • Hang it on a padded hanger.

  • Hold the steamer a few inches away and glide over the robe using slow, downward motions make sure to avoid the area with personalisation.

  • Let the robe air dry completely before wearing or folding.

Avoid: Aiming the steam directly at the heat-transferred vinyl text, the heat will cause the adhesive to melt and the design to lift.

2. Shower Steam (No Tools Needed)

No steamer? No problem. Use your bathroom as a makeshift steaming chamber.

How to do it:

  • Hang your robe on a hanger on the back of the door or drape it flatly over a towel rack.

  • Run a hot shower (with the door closed) for 5-10 minutes.

  • Let the robe hang in the steam—but ensure it does not get wet—for a further 15–30 minutes.

  • Allow to air dry after in a well-ventilated area (not in direct sunlight).

Tip: This method works best for light to moderate creasing, especially after travel.

3. Iron with Extreme Caution

Ironing satin is risky but doable with care—especially if you’re dealing with stubborn creases.

How to do it:

  • Set your iron to the lowest heat setting, or a dedicated "satin" or "silk" setting.

  • Place a press cloth (like a cotton pillowcase or handkerchief) between the robe and the iron.

  • Iron in gentle strokes, avoiding the personalised area completely.

Never iron directly over vinyl lettering or screen printing—it can melt or warp the design.

4. Let It Hang Overnight

Sometimes the best method is simply time and gravity.

How to do it:

  • After unpacking your robe, hang it immediately on a padded or wooden hanger.

  • Light wrinkles often release on their own overnight or if you are going to be giving/wearing the robes days later then this should be the option you try first.

Final Tips for a Picture-Perfect Look:

  • Plan ahead: don't leave it until the last minute and give yourself enough time to wash, dry or de-crease your robe.

  • Test before steaming/pressing: If you’re unsure about the heat sensitivity of your personalised design, test on a small, hidden area first.

Smooth robe, smooth vibes. Whether you're getting glam with your bridesmaids or sharing a quiet moment before the ceremony, your satin bridal robe should feel as flawless as it looks. A little prep goes a long way in helping you feel your most confident (and camera-ready) on your big day.

Complete this form with your question or request: